Woodworking

whoo

whoo

<Silver Donator>
1,744
7,085
Bandwagon said:
Ok nevermind. Im not done. Looking at this thing with a flashlight, I can't leave it as is.

whoo whoo - do I need to sand this again in the 2k to 3k grit range? Or use a more aggressive cutting compound before polishing?

If its the former, can you recommend some good, high grit 5in disc brands?
View attachment 598258
Click to expand...

Well, without having been there through the process, I can't be 100% sure, but it looks like those scratches were there pre-polish so I'd sand back to 800 grit and wet sand up to 2000 or 3000 grit before buffing.

Mirka Abralon is expensive, but made for this kinda thing. You have to wet sand at lower speed.
 
  • 1Like
Reactions: 1 user
Bandwagon

Bandwagon

Kolohe
<Silver Donator>
25,630
69,550
whoo said:
Well, without having been there through the process, I can't be 100% sure, but it looks like those scratches were there pre-polish so I'd sand back to 800 grit and wet sand up to 2000 or 3000 grit before buffing.

Mirka Abralon is expensive, but made for this kinda thing. You have to wet sand at lower speed.
Click to expand...
They were definitely there prepolish. I thought the cutting compound would take them out. I'll check out mirka.

I did wet sand from 120-3k. What's the logic behind going slow? Keep the disc from bouncing?
 
whoo

whoo

<Silver Donator>
1,744
7,085
Bandwagon said:
They were definitely there prepolish. I thought the cutting compound would take them out. I'll check out mirka.

I did wet sand from 120-3k. What's the logic behind going slow? Keep the disc from bouncing?
Click to expand...
That's just specific to the Mirka Abralon. It's a thin sponge that holds water (or oil/solvent) and keeps the surfaces cooler and wetter for better swarf/dust/grit removal.

Also i would stop by a paint supply and get "wax wash remover" - if you can't get that, use mineral spirits. Wipe it down thoroughly between grits.

Kinda pricey at amazon, but this is the stuff.
Wax-Wash Remover - Amazon.com

Also comes in liquid. Great for surface prep before finishing, between coats, and before polishing, too.
 
  • 2Like
Reactions: 1 users
Cutlery

Cutlery

Kill All the White People
<Gold Donor>
7,636
23,254
IMG_20250817_222154975.jpg


This thing looks and feels spectacular.

Inside for a couple months now to cure before I send it to it's final home - a buddy 90 miles away so I don't have to look at the imperfections every day!
 
  • 5Like
Reactions: 4 users
Captain Suave

Captain Suave

Caesar si viveret, ad remum dareris.
5,926
10,157
Wood welding, new to me. Apparently by vibrating two pieces of wood against each other at precise pressure and frequency they can melt and fuse the lignin and hemicellulose and bond them together at least as well as modern glues.

 
  • 1WTF
Reactions: 1 user
Soygen

Soygen

The Dirty Dozen For the Price of One
<Nazi Janitors>
28,653
45,463
Captain Suave said:
Wood welding, new to me. Apparently by vibrating two pieces of wood against each other at precise pressure and frequency they can melt and fuse the lignin and hemicellulose and bond them together at least as well as modern glues.

Click to expand...

Finally a solid use for my epileptic cousin.
 
  • 1Wow!
  • 1Worf
Reactions: 1 users
Borzak

Borzak

Silver Baron of the Realm
27,132
36,424
Cutlery said:
View attachment 598413

This thing looks and feels spectacular.

Inside for a couple months now to cure before I send it to it's final home - a buddy 90 miles away so I don't have to look at the imperfections every day!
Click to expand...

Society of American Foresters had a very large conference table that was around 5" thick made out of Sugar Pine that took up the majority of the room. One day years after it was made and installed in the middle of a conference everyone was sitting around and a wood borer came out the top. That's what you need lol.
 
Cutlery

Cutlery

Kill All the White People
<Gold Donor>
7,636
23,254
Borzak said:
Society of American Foresters had a very large conference table that was around 5" thick made out of Sugar Pine that took up the majority of the room. One day years after it was made and installed in the middle of a conference everyone was sitting around and a wood borer came out the top. That's what you need lol.
Click to expand...

I thought about it, but I decided that's overblown.

I've got this entire tree. I slabbed it, flattened it, sanded it. I don't see any evidence of infestation anywhere along the line.
 
stupidmonkey

stupidmonkey

Not Smrt
<Gold Donor>
2,409
6,515
Captain Suave said:
Wood welding, new to me. Apparently by vibrating two pieces of wood against each other at precise pressure and frequency they can melt and fuse the lignin and hemicellulose and bond them together at least as well as modern glues.

Click to expand...

Thought I stumbled on a 70s porno on YouTube for moment there.
 
  • 1Worf
Reactions: 1 user
Captain Suave

Captain Suave

Caesar si viveret, ad remum dareris.
5,926
10,157
Pretty interesting new sharpening jig from Katz-Moses. I share his complaints about the existing clamshell/eclipse jigs. JKM products are affordable and quality in my experience. I have his router plane and really like it.

 
Last edited:
  • 2Like
Reactions: 1 users
Intrinsic

Intrinsic

Person of Whiteness
<Gold Donor>
16,218
15,491
I saw that pop up in my Instagram feed but forgot to go back and watch it. I have one of his fence stops and something else I can’t remember and have liked them.
 
Goatface

Goatface

Naxxramas 1.0 Raider
10,895
18,923
Cam / blacktail studio bought 17 acre farm and is going to build his dream shop. he is at the clueless farmer/building planning stage, but could get interesting.
www.youtube.com

Blacktail Ranch

I bought a farm, how hard can it be?
www.youtube.com www.youtube.com
 
You must log in or register to reply here.